Various steel cut wire shot machine is divided into three models: fully automatic, semi-automatic and manual type. Power are 7.5 kilowatts / hour. Automatic type, one-sided jobs, day (8 hours) more than 1600 kilograms of finished product, they both work to full capacity (8 hours) 3200 kg of finished product. It is our self-developed a new model, currently very popular in the market, it is not the most important feature of artificial feeding, labor, effort to make production workers away from the noise and pollution of iron powder. Semi-automatic, one-sided jobs, day (8 hours) more than 1500 kilograms of finished product, they both work to full capacity (8 hours) 3000 kg of finished product. It can cut barbed good raw material products, such as wire rope winding or a burr stubble, no points can be cut off root whole shares. Three models, can be cut 0.2 ~ 5.0mm wire diameter range can be used, the machine can be changed job status from 0.2mm to 5.0mm job status directly, without stopping in the middle and down the host and adjust tool than the original cost to the minicomputer fold increase, without leaving a steel head. Automatic Steel sand is popular on the market a new model, without manual feed, so production workers away from dust and noise, and higher efficiency models are generally more than doubled. 0.6--5.0 can cut wire diameter. Automatic steel cut wire shot machine can be used from 0.6 to 5.0, the machine can be changed from 0.6 job status directly to 5.0 job status, do not stop in the middle and down the host and adjust the tool. Than the original 6/100 economic growth, consumption, and the same general type. Steel head without leaving any point can be completely made of steel shot. When cutting steel 1.0mm or less when using run-gold surface to be polished, can not have a point of view. Worn to be sharp, quick, sharpens iron, (3) the angular size does not matter, do not touch the bottom of the knife until the alloy, the smaller the gap, the better. 1. 2mm cut above when sharpening alloys must be polished, alloy above need not be so sharp. 1.0 mm below the cut wire, sharpening given the most critical gaps, grinding bad nor good set, thick wire also easily used the knife cut filaments generally unhappy, do not direct the Brothers can be cut, stock split more than 1.6mm wire also cut about 400-500 kg, and a good cut. If you use a knife grinder mill is more accurate, but the angle by up later down the knife is not necessarily right, since the end of the knife and the big wheel angle precision is not so accurate, so when you set the knife, put a light bulb with a watch below, right angle straight into the trip, the gap as big as it can be. Note: 1, when the three-phase electrical connection must use two gates, a total gate of a sub-gate, the total gate 100A opening 60A. 2, when connected with a three-phase power, the voltage is 380V, 100A followed by a leakage breaker. 3, the use of more than one year to form a layer of oxide thread posts, should be re-take it. 4, the motor bearings plus a lubricant within a year. 5, before the boot, you should check all parts of the screws can not be loosened. 6, using the manual type of workers should wear a dust mask. 7, during normal operation of the machine, if unusual sound should immediately stop checks. 8, when the Brothers wear glasses and gloves. 9, when the temperature is high attention hot knife, the knife is not water cooled alloy. 10, rainy day, the rope above the water does not work, so as not to damage the tool. 11, the knife used for some time, watching carefully when sharpening, copper alloy and iron sets irrigation can not be reused if the pores, so as not to fall off the tool and equipment alloy collision, causing huge damage to the machine, not the knife alloy plastic filling is used up. 12, when the two alloy knife grinding wheel is better, because the grinding wheel is not the end of the knife used flat, while the alloy knife grinding wheel must be flat, such as uneven wear you is not accurate, it is not accurate cutting mill accomplished. Description: The first in a bed knife grinding wheel grinding bed knife Omo eyes, hands must be correct, grinding positive and polished (Figure 1), and then in the small wheel surface (see Figure 2) taper grinding, grinding finish later in the knife empty the outer edge of a small plane shall not exceed 1.5mm, if greater than 1.5mm, when you set the knife is not easy to use. Since the end of the knife at a fixed angle to see it (Fig. 6 H) (Fig. 7 low) so easy to use, easy to transport to do it without touching the knife, the knife if it is balanced at the end, you look at the gap between the fixed knife small. The new mill set a bad knife gap, but also to cut some time, can be a long time to die, then you think I set the gap is small, why cut a few die? Because you set the gap on the bottom edge is not a gap along the bottom edge of the sword. Then the mat beneath a thin iron knife seat, it looked up ,, so the gap is given on the knife and the bottom knife, cutting edge within the gap, so that it can cut more. Why leave a small plane 1.5mm, 1.5mm leave a small plane because Paul mouth, the mouth of the alloy has a great auxiliary force, durable and wear-resistant alloy, if you do not retain a small plane, grinding especially sharp, but you can not wear it accurate because there is no parallel lines. Why can not more than 1.5mm, if big, when given the knife blade can touch the bottom outer edge of a small plane, with seeing the gap can, in fact, knife and bottom inside edge gap is big, it is not a cut, it is not great. Contact: Li Huanhuan phone: 15634469733 QQ: 3157879902 Fixed: 0537-2213328 Fax: 0537-2889948 E-mail: 3157879902@qq.com